-
It is suitable for 2 jacks, complete with electric control device, 4 programmable pressure levels and hidden pressure programming controls. -
Oil tight, wear-proof, heat-resistant PVC gaskets for the steel moulds locking seal. -
- Triangular chamfer made of weldable rolled steel, supplied in abt 4.00 m long rods, 10x10mm.
- Triangular chamfer made of weldable rolled steel, supplied in abt 4.00 m long rods, 15x15 mm.
- Triangular chamfer made of weldable rolled steel, supplied in abt 4.00 m long rods, 20x20 mm.
- Triangular chamfer made of weldable rolled steel, supplied in abt 4.00 m long rods, 25x25 mm.
- Upon request, we also supply special milled sections.
-
The use of lifting anchors is the most widespread all along the years, the easiest and the cheapest one among all those existing on the market. Moreover, for the lifting of thin elements or beams with a thin core, the integral socket with reinforced bar is an insuperable product as it directly and quickly spreads the load in deepness. To be sure of adopting a good and safety lifting system, have a look to the same section referred to the anchor and for the choice and check of the socket, please consult the same section dedicated to the anchor. In the specific case of lifting sockets, the manufacturer guarantees that the breakage of the full system socket-articulated loop in axial pull happens at 4 times the nominal pull with which sockets are commercially individuated. Naturally, it is necessary to respect the distances from the edges and the minimum distances between centers of nearby sockets, to confine suitably each socket into the concrete with anchoring and distribution mesh. For construction details, please check the figures shown here. In any case, our technical-commercial office may inform you about the various types used and suggest to you the best, efficacious, sure and economical solution. -
Pre-stressing system includes the complete loosening of the strands before cutting them. -
GENERAL FEATURES
RPM per 1'
70
Power Kw
5,5
Weight Kg
430
Dimensions (LxLxH)
60x100x90
CUTTING CAPACITY
Bar
No.bars
No.bars
No.bars
No.bars
No.bars
1
2
3
4
5
Res.650N/mm²
Ø max 40
Ø max 26
Ø max 22
Ø max 18
Ø max 14
Res.850N/mm²
Ø max 36
Ø max 22
Ø max 18
Ø max 12
Ø max 10
-
GENERAL FEATURES RPM per 1' 100 Power Kw 3 Weight Kg 350 Dimensions (LxLxH) 53x92x75 CUTTING CAPACITY Bar No.bars No.bars No.bars No.bars No.bars 1 2 3 4 5 Res.650N/mm² Ø max 36 Ø max 24 Ø max 18 Ø max 16 Ø max 14 Res.850N/mm² Ø max 30 Ø max 20 Ø max 16 Ø max 14 Ø max 12 -
GENERAL FEATURES RPM per 1' 100 Power Kw 2,2 Weight Kg 260 Dimensions (LxLxH) 50x95x75 CUTTING CAPACITY Bar No.bars No.bars No.bars No.bars No.bars 1 2 3 4 5 Res.650N/mm² Ø max 32 Ø max 20 Ø max 16 Ø max 14 Ø max 12 Res.850N/mm² Ø max 26 Ø max 16 Ø max 12 Ø max 12 Ø max 8 -
GENERAL FEATURES RPM per 1' 110 Power Kw 2,2 Weight Kg 230 Dimensions (LxLxH) 45xx85x80 CUTTING CAPACITY Bar No.bars No.bars No.bars No.bars No.bars 1 2 3 4 5 Res.650N/mm² Ø max 26 Ø max 18 Ø max 14 Ø max 12 Ø max 10 Res.850N/mm² Ø max 22 Ø max 16 Ø max 12 Ø max 10 Ø max 8 -
To secure the mould side walls to the bottom, we suggest our self-locking system. Cod.: 84.0000012: Articulation stand Cod.: 84.0000013: Articulation -
To fix quickly the side walls of your steel moulds -
To fix quickly the side walls of your steel moulds. -
For closing the top of the moulds, we suggest our quick closing device by cam. -
Special sliding vibrators are available with pneumatic, hydraulic or mechanical locking device and pneumatic or electric vibrator. -
To reduce waste, the ideal solution for the recovery of long crop ends of strand is undoubtedly the coupler for plaits and strands. It consists of 2 clamps, whose diameter may vary, connected by a nipple. They are made from high quality steel and processed through severe heat treatment, which ensure many reuses and long life. COUPLERS SERVICING- Disassemble the clamp and soak all parts in heavy oil bath for 24 hours;
- Then clean all components with compressed air;
- Check the conditions of the knurl edge, replace wedges if necessary;
- Re-assemble the wedge sets with the elastic ring;
- Sprinkle graphite powder over wedges;
- Check wedges and socket for equal taper.
-
LIFTING CLUTCΗ is the re-usable component of the 'LIFTING SYSTEM', made of high resistance steel casting to guarantee lasting use. The lower end spheric part swings into the housing previously created into the concrete elements and its 'T' slot engages itself into the spheric head of the lifting anchor. The contact with the lifting anchor head is made during the lifting phase only when toe or spheric head is rested to the concrete element. -
Special compacting smoothing trowel for panels with aggregates in view. -
Prestressed long line casting bed for TT elements. Length: 36m - 65.5m - 72m - up to 120 m Shares of prestressing force: 250t - 350t - 500t - up to 800t Section with height from 300 to 1200 mm and width from 1200 to 2800mm Mould movement: manual or hydraulic Possibility to make moulds of the "slow" type, 'Self-reacting' type or with anchoring structure -
Height: variable; Tread: variable; Landing flight stair size: variable; Mould opening system: manual or hydraulic Vibration system: electric or pneumatic. -
Vibrating smoother for panels surface finishing -
For an accurate vibration of concrete even in special cases, whenever no vibration inside the formwork is possible, the solution is our sturdy pneumatic poker-type vibrator. Reliable, maintenance-free, totally safe. We propose our high-frequency, pneumatic vibrating pokers; they are bearing- and lubrication-free and consist of a wear-proof steel vibrating assembly, abrasion- and oil-proof rubber hose, silenced cock with air filter, 3/4” GAS connection. 6 Bar compressed air required. -
Main standard technical specifications:- Panel dimensions allowed: Thickness: any - Height: 3200mm divisible, (upon request over 3200mm) - Length: any;
- Adjustable traverse speed: usually 2.5 - 6m/min.;
- Electric feed: 400V, 50Hz;
- Electric Power allowed: 48-70-92 kW;
- Water network feed: 90/180/270 l/min., pressure 1.5 bar;
- Water pressure during washing operation: adjustable 60-120 bar;
- Pump: piston type per 120 bar max., flow rate: 110 l/min.;
- Brushes with vertical motion: n. 02x3500mm;
- Support of trolleys: traverse on rails.
