-
The stairs element is constituted by a suitably shaped polystyrene core, wherein the rise and tread may vary according to the needs of the project. This element must be reinforced and completed on site. -
This panel is used for the construction of floors and roofs. The thickness and geometry of the panel can be varied according to the span and project requirements. The placement of the reinforcement and the concrete pour can be made totally on site or partially in the production plant. -
Pin for steel plate locking suitable for 20 mm diameter holes. Use together with wedge L=100-200 mm. Locking wedge, 100 mm long, to be used together with pins. -
To neutralize the effect of strands where a minor compression stress is required, the best solution to avoid operating difficulties of deviated strands is the soft sheath for the strand neutralization. Easy to apply, available for various sizes of strand and plaits, antioxidizing. Packs: • Yellow colour soft sheath for 0.6'' strand only, supplied into 3m long packs of 300m in total. • Red colour sheat idoneous for 3/8'',1/2'',0.6'' strands, supplied into 3m long packs of 600m in total • Sheat for 3x3 plait, supplied into 3m long packs of 1500m in total. -
Prestressed universal long line casting bed. Length: 36m up to 120 - 200m Shares of prestressing force: 300t - 500t - 800t - 1200t - 1600t up to 3600t Base width from 300 to 2500mm Mould movement: manual or hydraulic Possibility to make moulds of the 'slow' type, 'Self-reacting' type or with anchoring structure -
Main standard technical specifications:- Panel dimensions allowed: Thickness: any - Height: 3200mm divisible, (upon request over 3200mm) - Length: any;
- Adjustable traverse speed: usually 2.5 - 6m/min.;
- Electric feed: 400V, 50Hz;
- Electric Power allowed: 48-70-92 kW;
- Water network feed: 90/180/270 l/min., pressure 1.5 bar;
- Water pressure during washing operation: adjustable 60-120 bar;
- Pump: piston type per 120 bar max., flow rate: 110 l/min.;
- Brushes with vertical motion: n. 02x3500mm;
- Support of trolleys: traverse on rails.
-
For an accurate vibration of concrete even in special cases, whenever no vibration inside the formwork is possible, the solution is our sturdy pneumatic poker-type vibrator. Reliable, maintenance-free, totally safe. We propose our high-frequency, pneumatic vibrating pokers; they are bearing- and lubrication-free and consist of a wear-proof steel vibrating assembly, abrasion- and oil-proof rubber hose, silenced cock with air filter, 3/4” GAS connection. 6 Bar compressed air required. -
Vibrating smoother for panels surface finishing -
Height: variable; Tread: variable; Landing flight stair size: variable; Mould opening system: manual or hydraulic Vibration system: electric or pneumatic. -
Prestressed long line casting bed for TT elements. Length: 36m - 65.5m - 72m - up to 120 m Shares of prestressing force: 250t - 350t - 500t - up to 800t Section with height from 300 to 1200 mm and width from 1200 to 2800mm Mould movement: manual or hydraulic Possibility to make moulds of the "slow" type, 'Self-reacting' type or with anchoring structure -
Special compacting smoothing trowel for panels with aggregates in view. -
LIFTING CLUTCΗ is the re-usable component of the 'LIFTING SYSTEM', made of high resistance steel casting to guarantee lasting use. The lower end spheric part swings into the housing previously created into the concrete elements and its 'T' slot engages itself into the spheric head of the lifting anchor. The contact with the lifting anchor head is made during the lifting phase only when toe or spheric head is rested to the concrete element. -
To reduce waste, the ideal solution for the recovery of long crop ends of strand is undoubtedly the coupler for plaits and strands. It consists of 2 clamps, whose diameter may vary, connected by a nipple. They are made from high quality steel and processed through severe heat treatment, which ensure many reuses and long life. COUPLERS SERVICING- Disassemble the clamp and soak all parts in heavy oil bath for 24 hours;
- Then clean all components with compressed air;
- Check the conditions of the knurl edge, replace wedges if necessary;
- Re-assemble the wedge sets with the elastic ring;
- Sprinkle graphite powder over wedges;
- Check wedges and socket for equal taper.
-
Special sliding vibrators are available with pneumatic, hydraulic or mechanical locking device and pneumatic or electric vibrator. -
For closing the top of the moulds, we suggest our quick closing device by cam. -
To fix quickly the side walls of your steel moulds. -
To fix quickly the side walls of your steel moulds -
To secure the mould side walls to the bottom, we suggest our self-locking system. Cod.: 84.0000012: Articulation stand Cod.: 84.0000013: Articulation -
GENERAL FEATURES RPM per 1' 110 Power Kw 2,2 Weight Kg 230 Dimensions (LxLxH) 45xx85x80 CUTTING CAPACITY Bar No.bars No.bars No.bars No.bars No.bars 1 2 3 4 5 Res.650N/mm² Ø max 26 Ø max 18 Ø max 14 Ø max 12 Ø max 10 Res.850N/mm² Ø max 22 Ø max 16 Ø max 12 Ø max 10 Ø max 8 -
GENERAL FEATURES RPM per 1' 100 Power Kw 2,2 Weight Kg 260 Dimensions (LxLxH) 50x95x75 CUTTING CAPACITY Bar No.bars No.bars No.bars No.bars No.bars 1 2 3 4 5 Res.650N/mm² Ø max 32 Ø max 20 Ø max 16 Ø max 14 Ø max 12 Res.850N/mm² Ø max 26 Ø max 16 Ø max 12 Ø max 12 Ø max 8 -
GENERAL FEATURES RPM per 1' 100 Power Kw 3 Weight Kg 350 Dimensions (LxLxH) 53x92x75 CUTTING CAPACITY Bar No.bars No.bars No.bars No.bars No.bars 1 2 3 4 5 Res.650N/mm² Ø max 36 Ø max 24 Ø max 18 Ø max 16 Ø max 14 Res.850N/mm² Ø max 30 Ø max 20 Ø max 16 Ø max 14 Ø max 12 -
GENERAL FEATURES
RPM per 1'
70
Power Kw
5,5
Weight Kg
430
Dimensions (LxLxH)
60x100x90
CUTTING CAPACITY
Bar
No.bars
No.bars
No.bars
No.bars
No.bars
1
2
3
4
5
Res.650N/mm²
Ø max 40
Ø max 26
Ø max 22
Ø max 18
Ø max 14
Res.850N/mm²
Ø max 36
Ø max 22
Ø max 18
Ø max 12
Ø max 10
