-
Internal Spider is a safe clamp with small dimensions which, thanks to its innovative shape allows the hooking of the rewinded coils from the inside. -
To reduce waste, the ideal solution for the recovery of long crop ends of strand is undoubtedly the coupler for plaits and strands. It consists of 2 clamps, whose diameter may vary, connected by a nipple. They are made from high quality steel and processed through severe heat treatment, which ensure many reuses and long life. COUPLERS SERVICING- Disassemble the clamp and soak all parts in heavy oil bath for 24 hours;
- Then clean all components with compressed air;
- Check the conditions of the knurl edge, replace wedges if necessary;
- Re-assemble the wedge sets with the elastic ring;
- Sprinkle graphite powder over wedges;
- Check wedges and socket for equal taper.
-
'QUICK LIFTING SYSTEM' offers a rational and reliable method for the handling of concrete elements. The connection and disconnection operations of the lifting clutch are instantaneous and allow hoisting 'on edge' of panels manufactured in horizontal with speed, safety and economy. The system does not foresee welded or bolted pieces, therefore laying time is minimum and there is no risk of faulty screwing or threads wear. The efficacity of the 'QUICK LIFTING SYSTEM' is proven by its use on sites since many years. The components of the 'QUICK LIFTING SYSTEM' are the lifting anchor, the lifting clutch and the salvage round recess plug which, previously fixed inside the mould, provides a void housing into concrete such as to allow the lifting anchor head to be hooked by the lifting clutch.
-
LIFTING CLUTCΗ is the re-usable component of the 'LIFTING SYSTEM', made of high resistance steel casting to guarantee lasting use. The lower end spheric part swings into the housing previously created into the concrete elements and its 'T' slot engages itself into the spheric head of the lifting anchor. The contact with the lifting anchor head is made during the lifting phase only when toe or spheric head is rested to the concrete element.
-
Multi-rotor straightening center using coils up to Ø 20mm for the production of straight bars. - 4 wheel drive pulling unit driven by servomotors for high speed production; - Maximum pulling speed 140 m/minute; - The straightening system uses rotors, each one dedicated to a single bar diameter which guarantees perfectly straight bars and wire diameter changes in just a few seconds; - Servomotor driven cutting unit guarantees high speed and high cutting accuracy; - Twin Version (Optional) with double cutter, double channel, double pulling unit: it allows the processing of two bars simultaneously, doubling the productivity of the machine. It can be equipped with: - Bundle aligning device on the ground with vibrators (Optional); - Indexing carriage for the automatic collection and sorting of the bars produced (Optional); - Storage rack pneumatically operated (Optional). -
Multi-rotor straightening and shaping center using coils up to Ø 20mm for the production of straight bars, large stirrups and shapes with bends on both ends. - 4 wheel drive pulling unit driven by servomotors for high speed production; - Maximum pulling speed 140 m/minute; - The straightening system uses rotors, each one dedicated to a single bar diameter which guarantees perfectly straight bars and wire diameter changes in just a few seconds; - Servomotor driven cutting unit guarantees high speed and high cutting accuracy; - 2 bidirectional bending units work “off-line” so the bars are bent in “masked time”; - Automatic bending tooling changeover for higher productivity; - Indexing carriage for the automatic collection and sorting of the bars produced. -
Local Optimo is an important optimization software allowing to work on the machine’s computer. The software optimizes the cutting lengths by minimizing scraps. -
Machine for automated assembling of mesh cages of AAC panels by welding of vertical connectors. AAC panels are used in the production of floors and roofs, external walls and interior partitions. Driven by digital electric servomotors. -
Manual bending line for the fabrication of bars bent on one or both ends. Composed of 2 bending units P45 or P60 and the bending bench MFC PRO with arms for automatic loading and unloading of the bars. -
Capacity: 6m³ of concrete
-
Thanks to its innovating system, Mega Genius takes, counts and moves the bars for shear-line feeding in a completely automatic way. With Mega Genius you save money and enhance productivity due to its flexibility. Advantages:- ‘Mega Genius’ is extremely fast so it can feed more bars compared with manual feeding. The result is higher productivity per hour for any kind of shear line.
- No need of hard and dangerous bar handling so no need of people for such operation resulting in great money saving.
- The elimination of manual bar feeding enhances security at job site.
- “Mega Genius” special structure makes it possible to feed shear-lines with higher a number of bars of different diameter and length resulting in:
- drastic reduction in machine set-up;
- plant overall dimensions determined by clients’ room available;
- higher flexibility of the plant.
- The possibility to optimize cutting procedures means reducing scraps.
